Bandai FCG board
From NESdev Wiki
Jump to navigationJump to search
Bandai FCG boards are used largely by Bandai for Dragon Ball and Gundam games, as well as a few others. One IREM title uses it as well.
These boards contain one of Bandai's FCG mapper chips.
Hardware: PRG ROM (16 KiB banks, one switchable and one fixed), CHR ROM (1 KiB banks), no PRG RAM, optional I²C EEPROM (24C02 or 24C01).
Three mappers are used to describe these boards
- iNES Mapper 016 is intended for use with boards which contain a 24C02 256-byte serial EEPROM (but may contain none)
- iNES Mapper 153 is a rarely used assignment for a customized board with no EEPROM and SRAM in its place.
- iNES Mapper 159 is intended for use with boards which contain a 24C01 128-byte serial EEPROM
You may encounters roms with 016/159 assignments mixed up. There used to be no distinction when 016 was first assigned. The distinction was introduced later to distinguish the 128-byte boards from the 256-byte or no-EEPROM boards. In NES 2.0 format, there is still no distinction because the "battery backed PRG RAM size" field completely disambiguates these boards, though emulators MAY display a warning when the RAM size field is abnormal for a given mapper.
FCEUX does not emulate the EEPROM. It seems that returning 0x00 from EEPROM registers suffices to get most games booting.
Ports
The mapper's ports are mirrored at $6000-$FFFF, except for the EEPROM I/O register which can only be read at $6000-$7FFF.
- $8000-$8007: Select 1024 byte CHR bank at $0000, $0400, ..., $1C00
- $8008: Select 16384 byte PRG bank at $8000 (the last bank is fixed at $C000)
- $8009: Mirroring (0: vertical; 1: horizontal; 2: 1-screen $2000; 3: 1-screen $2C00)
- $800A: IRQ control (0: pause; 1: count; any write acknowledges)
- $800B: Low 8 bits of IRQ counter
- $800C: High 8 bits of IRQ counter
- $800D: EEPROM write
When enabled, IRQ counts down by 1 every CPU cycle. /IRQ goes low when the counter goes from $0001 to $0000, and it goes high when $800A is written. The counter is not reloaded after IRQ; it'll fire once every 65536 cycles unless paused or reloaded with $800B/$800C writes.
Any read from $6000-$7FFF appears to read the EEPROM.
EEPROM appears to be laid out like this:
7 bit 0 $800D: EEPROM control |||' '''' ||+-------- Clock |+--------- Data in +---------- Enable Read 7654 3210 $6000-$7FFF: EEPROM read | +------ Data out
Some patterns observed in the games' save code:
- Start I/O: $00 $40 $60 $20 $00
- Write 0 bit: $00 $20 $00
- Write 1 bit: $00 $40 $60 $40 $00
- Acknowledge: $00 $20 $A0 Read $00
- Read bit: $60 $E0 Read $40
- Stop I/O: $00 $20 $60 $40 $C0
Just use the datasheets for the 24C01 and 24C02 they used when implementing the EEPROM:
- 24C01, has no device address/uses device address as memory address: http://www.alldatasheet.com/datasheet-pdf/pdf/56094/ATMEL/24C01.html
- That Disch below reports the 24C01 as being little endian is due to a mistake at Bandai, not a deviation from the datasheet.
- 24C02, with device address: http://www.atmel.com/Images/doc0180.pdf
Below, Disch was unfamiliar with I²C, so a number of his comments are solely from the point of view of someone unfamiliar with it.
Here is a lightly-edited version of Disch's original notes: ======================== = Mapper 016 = = + 153 = = + 159 = ======================== aka -------------------------- Bandai (something or other) Example Games: -------------------------- Dragon Ball - Dai Maou Jukkatsu (016) Dragon Ball Z Gaiden (016) Dragon Ball Z 2 (016) Rokudenashi Blues (016) Akuma-kun - Makai no Wana (016) Famicom Jump II: Saikyou no 7 Nin (153) Dragon Ball Z - Kyoushuu! Saiya Jin (159) SD Gundam Gaiden (159) Magical Taruruuto Kun 1, 2 (159) Three Mappers: --------------------------- 016 and 159 are mapped the exact same way. Registers are all the same and whatnot. And in fact, for a while, both mappers were assigned the same mapper number (016). Therefore, you may come across mapper 159 games that are still marked as mapper 016. The difference between the two is in the EEPROM. These mappers don't have traditional SRAM (I couldn't tell you why). Instead, they have an I²C EEPROM that has to be written to one bit at a time, resulting in very strange-seeming register writes. Mapper 016 has 256 bytes of EEPROM, and is accessed high bit first Mapper 159 has 128 bytes of EEPROM, and is accessed low bit first For further details, see the section at the bottom. Apart from EEPROM, the mappers are 100% identical in function.
153 (as far as we know used exclusively for Famicom Jump II: Saikyou no 7 Nin) has SRAM instead of an EEPROM.
Notes:
---------------------------
Since there's EEPROM, there's no SRAM (EEPROM is used to save games).
Registers:
---------------------------
Range,Mask: $6000-FFFF, $000F
Note: below regs are listed as $800x, but note they also exist at $6000-7FFF
$8000-8007: CHR Regs
$8008: PRG Reg (16k @ $8000)
$8009: [.... ..MM] Mirroring:
%00 = Vert
%01 = Horz
%10 = 1ScA
%11 = 1ScB
$800A: [.... ...E] IRQ Enable (0=disabled)
$800B: Low 8 bits of IRQ Counter
$800C: High 8 bits of IRQ Counter
$800D: EEPROM I/O
another note: since PRG is mapped to $8000-FFFF, EEPROM I/O reg can only be read via $6xxx or $7xxx. To my
knowledge no other registers are readable. It also appears that reading from *ANY* address in $6xxx-7xxx
will read the EEPROM I/O reg. Rokudenashi Blues will poll $7F00 and will wait for bit 4 to be 0 before
continuing (so if you're giving open bus @ 7F00, the game will deadlock)
CHR Setup:
---------------------------
$0000 $0400 $0800 $0C00 $1000 $1400 $1800 $1C00
+-------+-------+-------+-------+-------+-------+-------+-------+
| $8000 | $8001 | $8002 | $8003 | $8004 | $8005 | $8006 | $8007 |
+-------+-------+-------+-------+-------+-------+-------+-------+
PRG Setup:
---------------------------
$8000 $A000 $C000 $E000
+---------------+---------------+
| $8008 | { -1} |
+---------------+---------------+
IRQs:
---------------------------
IRQs are nice and simple.
When enabled, the 16-bit IRQ counter counts down every CPU cycle, wrapping from $0000->FFFF. When the
counter makes the transition from $0001->$0000, an IRQ is generated.
When disabled, the IRQ counter does not count.
Any write to $800A will acknowledge the IRQ
$800B and $800C change the IRQ counter directly -- not a reload value.
EEPROM:
---------------------------
EEPROM is a real nightmare. Nobody knew exactly how it worked -- but by examining the game code,
patterns surface. Games do a series of extremely cryptic writes to $800D, and occasionally read a single
bit from $800D. By examining some logs I made of the games I've noticed a small bit of patterns which I
list below, along with my guess as to what the game is attempting to do by performing that pattern:
write $00
write $40
write $60 Start I/O
write $20
write $00
write $00
write $20 Output '0' bit
write $00
write $00
write $40
write $60 Output '1' bit
write $40
write $00
write $00
write $20
write $A0 I have absolutly no clue
Read
write $00
write $60
write $E0 Read a single bit
Read
write $40
write $00
write $20
write $60 Stop I/O
write $40
write $C0
These likely aren't the only patterns that games perform. I recall seeing occasional writes of $80 and
other stuff thrown in there in some games. Also -- not all games follow this pattern, so looking for these
specific writes will not work for at least one other game.
It seems that only bits 5-7 of the written value are relevent (hereon, they will be referred to as D5 - D7).
Bit 4 ($10) is the only significant bit when read. Other bits are most likely open bus.
When writing bytes to EEPROM, games will generally perform 8 "output" patterns (either output 0 or output 1,
depending on the bits it wants to write), followed by a 9th output pattern, which I would assume finalizes
the write and/or possibly moves the 8 bits from a latch to EEPROM.
When reading bytes, games will generally perform 8 "read" patterns, followed by a single output pattern
(which I would assume finalizes the read).
Sometimes when the game is writing bits, it's writing data to be stored on EEPROM, and other times it's
setting the desired EEPROM address and/or read/write mode. Knowing which it's doing involves keeping track
of the state it's currently it and what it has done last, etc, etc.
But again -- nobody *really* knows how it works. The method I've employed in my emu is outlined below -- and
it appears to work for every game I've tried, but I *KNOW* it's not accurate. But, short of some hardware
guru acquiring a handful of these carts and doing a thorough RE job, that's about the best anyone can do.
Emulating EEPROM:
-----------------------
SUPER FAT IMPORTANT NOTE: This is just the method of EEPROM emulation I employ in my emu.
***THIS IS NOT HOW THE ACTUAL HARDWARE WORKS***
Do not use this as a final word or anything -- this is simply the product of lots of guesswork, speculation,
and trial and error.
D5 appears to be the "trigger" bit, and D6 appears to be the "signal" bit. I have no clue what D7 does, and
ignoring it completely has worked for me (though I'm sure it does have some purpose). "Commands" are sent
by toggling D5 (0->1->0). Two states of D6 are observed -- one when D5 rises (0->1), and one when it falls
(1->0). Using these two observed states, you get 4 possible commands. The command is sent when D5 falls.
Example:
byte D6 D5
write: $00 0 0
write: $40 1 0
write: $60 1 1 <-- D5 rise: D6=1
write: $40 1 0 <-- D5 fall: D6=1, command "1,1" sent here
write: $00 0 0
The above sequence would issue a "1,1" command.
Commands:
Name rise,fall example write sequence
------------------------------------------------
Write 0 0,0 $00, $20, $00
Write 1 1,1 $00, $40, $60, $40, $00
Open 1,0 $00, $40, $60, $20, $00
Close 0,1 $00, $20, $60, $40, $C0
The unit can be in one of several modes:
- Closed
- Select
- Address
- Write
- Read
I also use an 8-bit temporary value, an 8-bit address (or 7-bit address, if 128 byte EEPROM) and 9-step bit
counter.
I would assume the unit is Closed on startup (and possibly reset).
Basic Concept overview:
"Write 0" and "Write 1" commands advance the 9-step bit counter. The first 8 writes fill the appropriate
bit in the temporary value. The 9th write will take the temp value and move it to either the address (if in
Address mode), or to the desired area in EEPROM (if in Write mode), and the mode will update accordingly.
Basically the first 8 writes fill the temp value and the 9th moves it to where it needs to go.
Reads operate similarly... but the temp buffer isn't affected by the writes, and the 9th step doesn't copy
the temp value anywhere. Note however that games will perform a write between each bit read (presumably to
advance it to the next bit) -- so you should do nothing but return the appropriate bit when the game reads
the EEPROM I/O Reg (do not advance it to the next bit on read).
"Select" mode exists on 256 byte EEPROM only (mapper 016). It is used to select between read/write mode.
Bit 0 of the 8-bit value written when in Select mode determines read/write mode. On 128 byte EEPROM (mapper
159), the high bit of the address selects read/write mode. In both cases, 1=read mode, 0=write mode.
Remember that on 128 byte, values are written low bit first... but on 256 byte, they're written high bit
first. Bits are read the same order they're written.
Doing anything but opening when the unit is closed has no effect.
Logic Flow Details (256-byte ... mapper 016)
--------------------------------------------
Opening from Closed Mode:
a) Enter Select Mode
Opening from non-Closed Mode:
a) if in Select Mode, increment address by 1
b) enter Select Mode.
c) Reset bit counter (next write is the first write in the 9-write sequence)
Writing in Select Mode:
a) If low bit of written value = 1
-) Enter Read Mode
b) otherwise...
-) Enter Address Mode
Writing in Address Mode:
a) written value becomes address
b) Enter Write mode
Writing in Write Mode:
a) written value moves to current address of EEPROM
b) mode is not changed
Writing in Read Mode:
a) Enter Select Mode
Logic Flow Details (128-byte ... mapper 159)
--------------------------------------------
Opening from Closed Mode:
a) Enter Address Mode
Opening from non-Closed Mode:
a) increment address by 1 (wrap $7F->00)
b) do not change mode
c) Reset bit counter (next write is the first write in the 9-write sequence)
Writing in Address Mode:
a) written value becomes address (low 7 bits only)
b) if high bit of written value is set...
-) Enter Read Mode
c) otherwise...
-) Enter Write Mode
Writing in Write Mode:
a) written value moves to current address of EEPROM
b) Enter Address mode
Writing in Read Mode:
a) Enter Address Mode
