APU Sweep: Difference between revisions
m (standard pronunciation of "NES" is "en ee ess", so "an") |
(Make calculation of target period more distinct as a step in the sweep unit's operation; reiterate approximate rate of APU Frame Counter) |
||
Line 20: | Line 20: | ||
|} | |} | ||
'' | The sweep unit continuously calculates each channel's '''target period''' in this way: | ||
# A barrel shifter shifts the channel's 11-bit [[APU Pulse|raw timer period]] right by the shift count, producing the change amount. | |||
# If the negate flag is true, the change amount is made negative. | |||
# The target period is the sum of the current period and the change amount. | |||
When | Thus whenever the current period changes for any reason, whether by $400x writes or by sweep, the target period also changes. | ||
When the [[APU Frame Counter|frame counter]] sends a half-frame clock (at 120 or 96 Hz), one of three things happens: | |||
* If the reload flag is set, the divider's counter is set to the period P. If the divider's counter was zero before the reload and the sweep is enabled, the pulse's period is also adjusted (if the target period is in range; see below). The reload flag is then cleared. | * If the reload flag is set, the divider's counter is set to the period P. If the divider's counter was zero before the reload and the sweep is enabled, the pulse's period is also adjusted (if the target period is in range; see below). The reload flag is then cleared. | ||
Line 28: | Line 33: | ||
* If the reload flag is clear and the divider's counter is zero and the sweep is enabled, the counter is set to P and the pulse's period is adjusted (if the target period is in range; see below). | * If the reload flag is clear and the divider's counter is zero and the sweep is enabled, the counter is set to P and the pulse's period is adjusted (if the target period is in range; see below). | ||
When the channel's ''current'' period is less than 8 or the target period is greater than $7FF, the channel is silenced (0 is sent to the [[APU Mixer|mixer]]) but the channel's current period remains unchanged. Otherwise, if the enable flag is set and the shift count is non-zero, when the divider outputs a clock, the channel's period is updated. | |||
If the shift count is zero, the channel's period is never updated, but the channel will ''still'' be silenced if the sweep is in add mode and the target period (i.e., the current period added to itself) is greater than $7FF. | If the shift count is zero, the channel's period is never updated, but the channel will ''still'' be silenced if the sweep is in add mode and the target period (i.e., the current period added to itself) is greater than $7FF. | ||
Because the target period is computed continuously, a target period overflow from the sweep unit's adder can silence a channel ''even when the enabled flag is clear'' and even when the sweep divider is not outputting a clock signal. To fully disable a sweep unit, write $08 to turn on the negate flag so that the target period is not greater than the channel's period and therefore not greater than $7FF. (This behavior of silencing the channel even when the sweep unit is disabled is only relevant for adder overflow; the pulse channels are ''always'' silenced when the period is less than eight, regardless of whether a sweep period update or an explicit setting of the period was involved.) | |||
For reasons unknown, pulse channel 1 hardwires its adder's carry input rather than using the state of the negate flag, resulting in the subtraction operation adding the '''one's complement''' instead of the expected two's complement (as pulse channel 2 does). As a result, a negative sweep on pulse channel 1 will subtract the shifted period value '''minus 1'''. | For reasons unknown, pulse channel 1 hardwires its adder's carry input rather than using the state of the negate flag, resulting in the subtraction operation adding the '''one's complement''' instead of the expected two's complement (as pulse channel 2 does). As a result, a negative sweep on pulse channel 1 will subtract the shifted period value '''minus 1'''. |
Revision as of 16:11, 28 December 2016
An NES APU sweep unit can be made to periodically adjust a pulse channel's period up or down.
Each sweep unit contains the following: divider, reload flag.
$4001 | EPPP.NSSS | Pulse channel 1 sweep setup (write) |
$4005 | EPPP.NSSS | Pulse channel 2 sweep setup (write) |
bit 7 | E--- ---- | Enabled flag |
bits 6-4 | -PPP ---- | The divider's period is set to P + 1 |
bit 3 | ---- N--- | Negate flag 0: add to period, sweeping toward lower frequencies 1: subtract from period, sweeping toward higher frequencies |
bits 2-0 | ---- -SSS | Shift count (number of bits) |
Side effects | Sets the reload flag |
The sweep unit continuously calculates each channel's target period in this way:
- A barrel shifter shifts the channel's 11-bit raw timer period right by the shift count, producing the change amount.
- If the negate flag is true, the change amount is made negative.
- The target period is the sum of the current period and the change amount.
Thus whenever the current period changes for any reason, whether by $400x writes or by sweep, the target period also changes.
When the frame counter sends a half-frame clock (at 120 or 96 Hz), one of three things happens:
- If the reload flag is set, the divider's counter is set to the period P. If the divider's counter was zero before the reload and the sweep is enabled, the pulse's period is also adjusted (if the target period is in range; see below). The reload flag is then cleared.
- If the reload flag is clear and the divider's counter is non-zero, it is decremented.
- If the reload flag is clear and the divider's counter is zero and the sweep is enabled, the counter is set to P and the pulse's period is adjusted (if the target period is in range; see below).
When the channel's current period is less than 8 or the target period is greater than $7FF, the channel is silenced (0 is sent to the mixer) but the channel's current period remains unchanged. Otherwise, if the enable flag is set and the shift count is non-zero, when the divider outputs a clock, the channel's period is updated.
If the shift count is zero, the channel's period is never updated, but the channel will still be silenced if the sweep is in add mode and the target period (i.e., the current period added to itself) is greater than $7FF.
Because the target period is computed continuously, a target period overflow from the sweep unit's adder can silence a channel even when the enabled flag is clear and even when the sweep divider is not outputting a clock signal. To fully disable a sweep unit, write $08 to turn on the negate flag so that the target period is not greater than the channel's period and therefore not greater than $7FF. (This behavior of silencing the channel even when the sweep unit is disabled is only relevant for adder overflow; the pulse channels are always silenced when the period is less than eight, regardless of whether a sweep period update or an explicit setting of the period was involved.)
For reasons unknown, pulse channel 1 hardwires its adder's carry input rather than using the state of the negate flag, resulting in the subtraction operation adding the one's complement instead of the expected two's complement (as pulse channel 2 does). As a result, a negative sweep on pulse channel 1 will subtract the shifted period value minus 1.