MOD RF: Difference between revisions
From NESdev Wiki
Jump to navigationJump to search
(→Parts List: Saving work...) |
m (→Parts List: air coil inductors are usually not very inductive, add missing µ s) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 13: | Line 13: | ||
*D1-4: "N 8" rectifier diodes | *D1-4: "N 8" rectifier diodes | ||
*L1: 2.2µH 20% inductor | *L1: 2.2µH 20% inductor | ||
*L3: 0. | *L3: 0.48µH hand-wound inductor | ||
*L4: 0. | *L4: 0.39µH hand-wound inductor | ||
*L6: 0. | *L6: 0.32µH hand-wound inductor | ||
*L8: 220nH inductor | |||
*L9: 68µH 20% inductor | *L9: 68µH 20% inductor | ||
*L?: 0.1µH hand-wound inductor | |||
*Q1,Q4-5: 2SC1740 NPN transistor | |||
*Q2: 2SC461 NPN transistor (Must use VHF-capable speeds if substituting) | |||
*R7: 15K Ohms 5% resistor | |||
*R19: 1K Ohms 5% resistor | |||
*R20: 1.8K Ohms 5% resistor | |||
*R22: 10K Ohms 5% resistor | |||
*R24: 105 Ohms 5% resistor | |||
*R25: 82 Ohms 5% resistor | |||
====Schematics==== | ====Schematics==== | ||
[[ | [[Image:GLEEOfl_full.jpg|200px]] | ||
Components as placed on non-solder side of board. | Components as placed on non-solder (through-hole component) side of board. | ||
===Mitsumi=== | ===Mitsumi=== | ||
====Parts List==== | ====Parts List==== | ||
====Schematics==== | ====Schematics==== | ||
Latest revision as of 00:44, 15 October 2014
This is a description of the daughterboard attached to the main NES logic board with a 5-pin soldered header.
Versions
Alps
Parts List
Note: Surface-mount and uninstalled components are not listed
- C19-20: R 472M 4700pF 2KV ceramic disc capacitors
- C21: 2200µF 25V electrolytic capacitor
- C23: 100µF 25V electrolytic capacitor
- C25: 100µF 10V electrolytic capacitor
- C29,C35: 1µF 50V electrolytic capacitors
- C36: 10µF 16V electrolytic capacitor
- D1-4: "N 8" rectifier diodes
- L1: 2.2µH 20% inductor
- L3: 0.48µH hand-wound inductor
- L4: 0.39µH hand-wound inductor
- L6: 0.32µH hand-wound inductor
- L8: 220nH inductor
- L9: 68µH 20% inductor
- L?: 0.1µH hand-wound inductor
- Q1,Q4-5: 2SC1740 NPN transistor
- Q2: 2SC461 NPN transistor (Must use VHF-capable speeds if substituting)
- R7: 15K Ohms 5% resistor
- R19: 1K Ohms 5% resistor
- R20: 1.8K Ohms 5% resistor
- R22: 10K Ohms 5% resistor
- R24: 105 Ohms 5% resistor
- R25: 82 Ohms 5% resistor
Schematics
Components as placed on non-solder (through-hole component) side of board.
