|
|
| (2 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| [[Category:iNES Mappers|009]][[Category:in NesCartDB|009]] | | #REDIRECT [[MMC2]] |
| | | {{DEFAULTSORT:009}}[[Category:iNES Mappers]][[Category:in NesCartDB]][[Category:Nintendo licensed mappers]] |
| [[iNES Mapper 009]] represents the [[PxROM]] boards, which use the [[Nintendo MMC2]] chip.
| |
| | |
| Here are Disch's original notes:
| |
| ========================
| |
| = Mapper 009 =
| |
| ========================
| |
|
| |
| aka
| |
| --------------------------
| |
| [[MMC2]]
| |
| [[PxROM]]
| |
|
| |
|
| |
| Example Game:
| |
| --------------------------
| |
| Mike Tyson's Punch Out!!
| |
|
| |
|
| |
| Registers:
| |
| ---------------------------
| |
|
| |
| Range,Mask: $A000-FFFF, $F000
| |
|
| |
|
| |
| $A000: PRG Reg
| |
| $B000: CHR Reg 0A
| |
| $C000: CHR Reg 0B
| |
| $D000: CHR Reg 1A
| |
| $E000: CHR Reg 1B
| |
| $F000: [.... ...M] Mirroring:
| |
| 0 = Vert
| |
| 1 = Horz
| |
|
| |
|
| |
|
| |
| PRG Setup:
| |
| ---------------------------
| |
| $8000 $A000 $C000 $E000
| |
| +-------+-------+-------+-------+
| |
| | $A000 | { -3} | { -2} | { -1} |
| |
| +-------+-------+-------+-------+
| |
|
| |
|
| |
|
| |
| CHR Setup:
| |
| ---------------------------
| |
| $0000 $0400 $0800 $0C00 $1000 $1400 $1800 $1C00
| |
| +-------------------------------+-------------------------------+
| |
| | $B000 or $C000 | $D000 or $E000 |
| |
| +-------------------------------+-------------------------------+
| |
|
| |
|
| |
| Which reg is used depends on the state of the respective latch. See below.
| |
|
| |
|
| |
| Latch:
| |
| ---------------------------
| |
| There are two latches on the MMC2. One associated with the left pattern table ($0xxx) and another associated
| |
| with right ($1xxx). Each latch operates independently.
| |
|
| |
| Whenever tile $FD is fetched, the appropriate latch is cleared, and whenever tile $FE is fetched, the
| |
| appropriate latch is set. This allows games to do mid-scanline swapping automatically by having $FD and $FE
| |
| be special marker tiles.
| |
|
| |
| When the $0xxx latch is clear, $B000 is used. When set, $C000 is used.
| |
| When the $1xxx latch is clear, $D000 is used. When set, $E000 is used.
| |
|
| |
| The swap occurs after the tile is fetched, not before. So if the latch is clear, and tile $FE is loaded,
| |
| tile $FE from the first reg will be drawn to the screen, but the next tile drawn will be from the second reg.
| |
|
| |
| Latches can be manipulated by hand by reading from the appropriate PPU address ($0FDx, $0FEx, $1FDx, $1FEx)
| |
| via $2007.
| |
