Jaleco SS 88006 pinout: Difference between revisions
(oscillator pin directions are knowable from the datasheet) |
m (256KiB games have to have a trace for PRG A17...) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 27: | Line 27: | ||
'--------' | '--------' | ||
The integral OR gate on pin 26, intended for use with a 28-pin 128KiB CHR-ROM, seems to be too slow. [https://forums.nesdev.org/viewtopic.php?p=246719#p246719] | |||
To support a 28-pin 128KiB CHR-ROM, some PCBs include an external [[7432]]. | |||
The associated ADPCM IC is wired as: | The associated ADPCM IC is wired as: | ||
| Line 57: | Line 58: | ||
JF-23 does not have any jumpers; it is always wired as though J2, J3, and J5 were shorted. | JF-23 does not have any jumpers; it is always wired as though J2, J3, and J5 were shorted. | ||
Jaleco's 32-pin CHR ROMs are neither a JEDEC-standard pinout, nor the same as Nintendo's proprietary 32-pin CHR ROMs. Like Nintendo, pin 24 remained A16, and pin 2 became PPU /RD. However, on JF-37, A17 is instead on pin 30, and other PCBs don't have a trace for A17 at all. | No PCBs have been seen with J4 or J6 enabled, not even on boards that could support it. | ||
Jaleco's 32-pin CHR ROMs are neither a JEDEC-standard pinout, nor the same as Nintendo's proprietary 32-pin CHR ROMs. Like Nintendo, pin 24 remained A16, and pin 2 became PPU /RD. However, on JF-29, JF-37, and JF-40, A17 is instead on pin 30, and other PCBs don't have a trace for A17 at all. | |||
Source: [//forums.nesdev.org/viewtopic.php?t=19727] | Source: [//forums.nesdev.org/viewtopic.php?t=19727] | ||
Latest revision as of 13:08, 2 November 2024
Jaleco SS 88006: 42-pin 0.6" shrink DIP (Canonically mapper 18)
SS 88006
.---\/---.
(f) M2 -> |01 42| -- VCC
(frw) CPU A12 -> |02 41| -> PRG RAM +CE (w)
(f) CPU A13 -> |03 40| -> PRG RAM /CE (w) (Also shorted to RAM /OE)
(f) CPU A14 -> |04 39| -> PRG RAM /WE (w)
(r) PRG /CE <- |05 38| -> µPD775x /RESET
(r) PRG A15 <- |06 37| -> µPD775x /START
(r) PRG A14 <- |07 36| -> CIRAM A10 (f)
(r) PRG A13 <- |08 35| <- OR B (PPU /RD)
(r) PRG A16 <- |09 34| -> CHR A17 (r)
(r) PRG A17 <- |10 33| -> CHR A10 (r)
(r) PRG A18 <- |11 32| -> CHR A16 (r)
(frw) CPU A1 -> |12 31| -> CHR A11 (r)
(frw) CPU A0 -> |13 30| -> CHR A13 (r)
(frw) CPU D0 -> |14 29| -> CHR A12 (r)
(frw) CPU D1 -> |15 28| -> CHR A14 (r)
(frw) CPU D2 -> |16 27| -> CHR A15 (r)
(frw) CPU D3 -> |17 26| -> OR Y (unused)
(f) R/W -> |18 25| <- OR A (PPU A13)
(f) /ROMSEL -> |19 24| <- PPU A12 (f)
(f) /IRQ <- |20 23| <- PPU A11 (f)
GND -- |21 22| <- PPU A10 (f)
'--------'
The integral OR gate on pin 26, intended for use with a 28-pin 128KiB CHR-ROM, seems to be too slow. [1] To support a 28-pin 128KiB CHR-ROM, some PCBs include an external 7432.
The associated ADPCM IC is wired as:
µPD7755/6C
__ __
(I4) PRG D6 -> |01\/18| <- PRG D5 (I3)
(I5) PRG D7 -> |02 17| <- PRG D4 (I2)
(I6) GND -> |03 16| <- PRG D3 (I1)
(I7) GND -> |04 15| <- PRG D2 (I0)
(volume) R2 -> |05 14| <- /START
sound out <- |06 13| <- /CS (Always connected to GND)
(BUSY) <- |07 12| <- X1
/RESET -> |08 11| -> X2
GND -- |09 10| -- VCC
'------'
Most PCBs (JF-24, -25, -29, and -37 without RAM; JF-27 and -40 with RAM and without ADPCM) have jumpers to configure operation:
- 0 ohm through-hole jumpers on the component side:
- J1 connects CHR ROM /CE = pin 20 of 28 = pin 22 of 32 to PPU A13.
- J2 connects the same pin to the output of the OR gate.
- Cut-and-solder jumpers on the solder side:
- J3 connects SS 88006 pin 19 to card edge /ROMSEL
- J4 connects the same pin to the delayed copy of the same signal generated by the 7432.
- J5 connects SS 88006 pin 1 to card edge M2
- J6 connects the same pin to the delayed copy of the same signal generated by the 7432.
JF-23 does not have any jumpers; it is always wired as though J2, J3, and J5 were shorted.
No PCBs have been seen with J4 or J6 enabled, not even on boards that could support it.
Jaleco's 32-pin CHR ROMs are neither a JEDEC-standard pinout, nor the same as Nintendo's proprietary 32-pin CHR ROMs. Like Nintendo, pin 24 remained A16, and pin 2 became PPU /RD. However, on JF-29, JF-37, and JF-40, A17 is instead on pin 30, and other PCBs don't have a trace for A17 at all.
Source: [2]
