UxROM: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
(→‎Variants: Leaving out the additional quad-OR would act like SUROM in a way)
(Add note about homebrew and Chinese cartridges having PRG-RAM.)
 
(42 intermediate revisions by 10 users not shown)
Line 1: Line 1:
[[Category:Discrete_logic_mappers]]
{{Infobox_iNES_mapper
The generic designation [[UxROM]] refers to the Nintendo cartridge boards NES-[[UNROM]], NES-[[UOROM]], their [[Famicom|HVC]] counterparts, and clone boards. The [[iNES]] format assigns [[iNES Mapper 002|mapper 2]] to UxROM.
|name=UxROM
|company=Nintendo, others
|mapper=2
|nescartdbgames=155
|othermappers=[[iNES Mapper 094|094]], [[iNES Mapper 180|180]]
|complexity=Discrete logic
|boards=UNROM, UOROM
|prgmax=256K/4096K
|prgpage=16K + 16K fixed
|chrmax=8K
|chrpage=n/a
|busconflicts=Yes/No
}}
{{nesdbbox
|ines|2|iNES 002
|unif_wild|-U%ROM|UxROM
|unif_wild|UNROM|UNROM
|unif_wild|UOROM|UOROM
}}
[[Category:Mappers with CHR RAM]][[Category:Mappers with bus conflicts]][[Category:NES 2.0 mappers with submappers]]
The generic designation ''UxROM'' refers to the Nintendo cartridge boards ''NES-UNROM'', ''NES-UOROM'', [[iNES Mapper 094|HVC-UN1ROM]] their [[Famicom|HVC]] counterparts, and clone boards.


== Overview ==
* '''[[iNES]] Mapper 002''' is the implementation of the most common usage of UxROM compatible boards, described in this article.
* PRG ROM size: 128 KB for UNROM, 256 KB for UOROM (DIP-28/32 Nintendo pinout)
* [[iNES Mapper 094]] describes UN1ROM, used only in ''Senjou no Ookami''.
* PRG ROM bank size: 16 KB
* [[iNES Mapper 180]] describes a reconfiguration of UNROM used only in ''Crazy Climber''.
* PRG RAM: None
 
* CHR capacity: 8 KB RAM [[Category:Mappers with CHR RAM]]
Example games:
* CHR bank size: Not bankswitched
* ''Mega Man''
* Nametable [[mirroring]]: Solder pads select vertical or horizontal mirroring
* ''Castlevania''
* Subject to [[bus conflict]]s: Yes [[Category:Mappers with bus conflicts]]
* ''Contra''
* ''Duck Tales''
* ''Metal Gear''


== Banks ==
== Banks ==
Line 27: Line 49:
       ++++- Select 16 KB PRG ROM bank for CPU $8000-$BFFF
       ++++- Select 16 KB PRG ROM bank for CPU $8000-$BFFF
           (UNROM uses bits 2-0; UOROM uses bits 3-0)
           (UNROM uses bits 2-0; UOROM uses bits 3-0)
Emulator implementations of '''iNES mapper 2''' treat this as a full 8-bit bank select register, without bus conflicts. This allows the mapper to be used for similar boards that are compatible.
To make use of all 8-bits for a 4 MB PRG ROM, an [[NES 2.0]] header must be used ([[iNES]] can only effectively go to 2 MB).
The original UxROM boards used by Nintendo were subject to bus conflicts, and the relevant games all work around this in software.
Some emulators (notably FCEUX) will have bus conflicts by default, but others have none.
[[NES_2.0_submappers#002.2C_003.2C_007:_UxROM.2C_CNROM.2C_AxROM|NES 2.0 submappers]] were assigned to accurately specify whether the game should be emulated with bus conflicts.


== Hardware ==
== Hardware ==
The [[UNROM]] and [[UOROM]] boards contain a [[74161|74HC161]] binary counter used as a quad D latch (4-bit register) and a [[7432|74HC32]] quad OR gate to make one bank always visible.
The UNROM, UN1ROM, and UOROM boards contain a [[74161|74HC161]] binary counter used as a quad D latch (4-bit register) and a [[7432|74HC32]] quad 2-input OR gate to make one bank always visible.
 
The circuit behaves as if it were as follows:
<pre>
      /PRGSEL              A14  A13-A0
      |                      |      |
      |                      |      |
      | D2-D0-.      ,------'      |
      |      |    . |            |
      | ,-----+--.  |`+.            |
      | |Register+--+0  `.          |
      | `--------'  |    |__.      |
      |      |    |    |  |      |
      | R/W --'  7-+1  ,'  |      |
      |            | ,'    |      |
      |            |'      |      |
      |                    |      |
      ,+---------------------+-------+-----.
      |/CE              A16-A14  A13-A0    |
      |        128K by 8 bit ROM    D7-D0+-- to 2A03 data bus
      |                                    |
      `------------------------------------'
</pre>
(This diagram is for UNROM. UOROM has one more bit in the register, multiplexer output, and address input A17, and the multiplexer's other input is $F. Homebrew boards capable of 512 KiB have one more of each, and the multiplexer's input is $1F.)
 
The quad OR gate here acts as a multiplexer.
A [[7402|74HC02]] quad NOR gate can be used instead if the banks are stored in reverse order in the ROM. If the program is 128 KiB or smaller, the 7402 way leaves one NOR gate free to invert R/W into /OE to avoid [[bus conflict]]s.[http://forums.nesdev.org/viewtopic.php?p=111686#p111686]
 
If an actual multiplexer ([[74157|74HC157]] quad 2:1) is cheaper than an OR gate, a third-party UxROM-compatible board can use that instead of the 74HC32, as [http://forums.nesdev.org/viewtopic.php?p=93516#p93516 kyuusaku suggested].


== Variants ==
== Variants ==
The mapper used in Codemasters games published by [[Camerica]] extends UxROM with [[CIC]] defeat circuitry.
The [[iNES Mapper 071|mapper]] used in Codemasters games published by Camerica extends UxROM with [[CIC]] defeat circuitry.
 
Nintendo's [[iNES Mapper 094|HVC-UN1ROM]] board moves the bankswitching bits within the byte.
 
''Crazy Climber'' replaces the [[7432|74HC32]] quad-OR gate by a [[7408|74HC08]] quad-AND gate, so that the first bank is fixed at $8000-$bfff and the switchable bank is present at $c000-$ffff. This configuration is assigned to [[iNES Mapper 180]], which uses the same UNROM PCB.
 
With an 8-bit latch ([[74377|74HC377]] or an additional 74HC161) and an additional 74HC32 to control A18-A21, a third-party board implementing this mapper can switch 4 MiB of PRG ROM.
 
[[User:Sivak/Battle Kid 2: Mountain of Torment|Battle Kid 2: Mountain of Torment]] implements a 512kB UxROM mapper.
 
[[UNROM 512]] implements a superset of 512kB UxROM, with additional CHR-RAM banking and the possibility of flash save.
 
The homebrew game ''Alwa's Awakening'' adds 8 KiB of battery-backed PRG-RAM in the usual $6000-$7FFF address range. A few Subor educational cartridges have non-battery-backed PRG-RAM in the same range as well. Emulators should support this PRG-RAM at least in the presence of a NES 2.0 header that explicitly specifies it.


In theory, it would be possible to implement the bank select register with a [[74373]]/[[74374]]/[[74377]]/[[74573]] octal D latch along with an additional 74*32, allowing up to 4 megabytes of PRG ROM, but due to [[mask ROM]] cost in the NES era, no non-pirate NES cart used this much memory.
== See also ==
*[[Programming UNROM]]


Another conceivable configuration leaves out the additional 74*32 and provides a separate fixed bank for each set of 16 banks in a way reminiscent of [[SUROM]]. For example, when bank 20 is swapped into $8000, bank 31 is swapped into $C000. This would be useful for making multicarts.
== External links ==
*[http://nesdev.org/mappers.zip Comprehensive NES Mapper Document] by \Firebug\, information about mapper's initial state is inaccurate.
* NES mapper list by Disch [http://www.romhacking.net/documents/362/]
* [https://forums.nesdev.org/viewtopic.php?p=179581#p179581 Converting UNROM to UOROM]

Latest revision as of 12:15, 21 October 2024

UxROM
Company Nintendo, others
Games 155 in NesCartDB
Complexity Discrete logic
Boards UNROM, UOROM
PRG ROM capacity 256K/4096K
PRG ROM window 16K + 16K fixed
PRG RAM capacity None
CHR capacity 8K
CHR window n/a
Nametable mirroring Fixed H or V, controlled by solder pads
Bus conflicts Yes/No
IRQ No
Audio No
iNES mappers 002, 094, 180

The generic designation UxROM refers to the Nintendo cartridge boards NES-UNROM, NES-UOROM, HVC-UN1ROM their HVC counterparts, and clone boards.

  • iNES Mapper 002 is the implementation of the most common usage of UxROM compatible boards, described in this article.
  • iNES Mapper 094 describes UN1ROM, used only in Senjou no Ookami.
  • iNES Mapper 180 describes a reconfiguration of UNROM used only in Crazy Climber.

Example games:

  • Mega Man
  • Castlevania
  • Contra
  • Duck Tales
  • Metal Gear

Banks

  • CPU $8000-$BFFF: 16 KB switchable PRG ROM bank
  • CPU $C000-$FFFF: 16 KB PRG ROM bank, fixed to the last bank

Solder pad config

  • Horizontal mirroring : 'H' disconnected, 'V' connected.
  • Vertical mirroring : 'H' connected, 'V' disconnected.

Registers

Bank select ($8000-$FFFF)

7  bit  0
---- ----
xxxx pPPP
     ||||
     ++++- Select 16 KB PRG ROM bank for CPU $8000-$BFFF
          (UNROM uses bits 2-0; UOROM uses bits 3-0)

Emulator implementations of iNES mapper 2 treat this as a full 8-bit bank select register, without bus conflicts. This allows the mapper to be used for similar boards that are compatible.

To make use of all 8-bits for a 4 MB PRG ROM, an NES 2.0 header must be used (iNES can only effectively go to 2 MB).

The original UxROM boards used by Nintendo were subject to bus conflicts, and the relevant games all work around this in software. Some emulators (notably FCEUX) will have bus conflicts by default, but others have none. NES 2.0 submappers were assigned to accurately specify whether the game should be emulated with bus conflicts.

Hardware

The UNROM, UN1ROM, and UOROM boards contain a 74HC161 binary counter used as a quad D latch (4-bit register) and a 74HC32 quad 2-input OR gate to make one bank always visible.

The circuit behaves as if it were as follows:

      /PRGSEL               A14  A13-A0
       |                      |      |
       |                      |      |
       | D2-D0-.       ,------'      |
       |       |     . |             |
       | ,-----+--.  |`+.            |
       | |Register+--+0  `.          |
       | `--------'  |    |__.       |
       |       |     |    |  |       |
       | R/W --'   7-+1  ,'  |       |
       |             | ,'    |       |
       |             |'      |       |
       |                     |       |
      ,+---------------------+-------+-----.
      |/CE              A16-A14  A13-A0    |
      |         128K by 8 bit ROM     D7-D0+-- to 2A03 data bus
      |                                    |
      `------------------------------------'

(This diagram is for UNROM. UOROM has one more bit in the register, multiplexer output, and address input A17, and the multiplexer's other input is $F. Homebrew boards capable of 512 KiB have one more of each, and the multiplexer's input is $1F.)

The quad OR gate here acts as a multiplexer. A 74HC02 quad NOR gate can be used instead if the banks are stored in reverse order in the ROM. If the program is 128 KiB or smaller, the 7402 way leaves one NOR gate free to invert R/W into /OE to avoid bus conflicts.[1]

If an actual multiplexer (74HC157 quad 2:1) is cheaper than an OR gate, a third-party UxROM-compatible board can use that instead of the 74HC32, as kyuusaku suggested.

Variants

The mapper used in Codemasters games published by Camerica extends UxROM with CIC defeat circuitry.

Nintendo's HVC-UN1ROM board moves the bankswitching bits within the byte.

Crazy Climber replaces the 74HC32 quad-OR gate by a 74HC08 quad-AND gate, so that the first bank is fixed at $8000-$bfff and the switchable bank is present at $c000-$ffff. This configuration is assigned to iNES Mapper 180, which uses the same UNROM PCB.

With an 8-bit latch (74HC377 or an additional 74HC161) and an additional 74HC32 to control A18-A21, a third-party board implementing this mapper can switch 4 MiB of PRG ROM.

Battle Kid 2: Mountain of Torment implements a 512kB UxROM mapper.

UNROM 512 implements a superset of 512kB UxROM, with additional CHR-RAM banking and the possibility of flash save.

The homebrew game Alwa's Awakening adds 8 KiB of battery-backed PRG-RAM in the usual $6000-$7FFF address range. A few Subor educational cartridges have non-battery-backed PRG-RAM in the same range as well. Emulators should support this PRG-RAM at least in the presence of a NES 2.0 header that explicitly specifies it.

See also

External links