INES Mapper 037: Difference between revisions
m (Switch back about the CIC: Kinopio was testing in his CICless CopyNES.) |
(→Hardware: if the combining overbars stopped working for me, I should assume there are enough other people that that looked bad to that I should avoid overbars) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:iNES Mappers | {{DEFAULTSORT:037}}[[Category:iNES Mappers]][[Category:MMC3-like mappers]][[Category:Multicart mappers]][[Category:in NesCartDB]][[Category:Mappers with scanline IRQs]] | ||
[[iNES Mapper 037]] represents the Nintendo of Europe multicart "Super Mario Bros. + Tetris + Nintendo World Cup". It glues together 3 [[MMC3]]-compatible games in a single pak. | [[iNES Mapper 037]] represents the Nintendo of Europe multicart "Super Mario Bros. + Tetris + Nintendo World Cup". It glues together 3 [[MMC3]]-compatible games in a single pak. | ||
| Line 46: | Line 46: | ||
It is very likely that the support hardware is a [[74161|74HC161]] latch and a [[7400|74HC00]] quad NAND gate, based on the specific order that the traces enter the epoxy blob. The latch, just like in the discrete logic mappers that use it, latches the bottom 3 bits of the data bus when it is written to. (Below, we call the latched form of D0→Q0, D1→Q1, and D2→Q2). The NAND gates are arranged to calculate | It is very likely that the support hardware is a [[74161|74HC161]] latch and a [[7400|74HC00]] quad NAND gate, based on the specific order that the traces enter the epoxy blob. The latch, just like in the discrete logic mappers that use it, latches the bottom 3 bits of the data bus when it is written to. (Below, we call the latched form of D0→Q0, D1→Q1, and D2→Q2). The NAND gates are arranged to calculate | ||
(MMC3 PRG A16 out) = M16 (for brevity) | (MMC3 PRG A16 out) = M16 (for brevity) | ||
(PRG ROM A16 in) = Q0·Q1 + Q2·M16 = | (PRG ROM A16 in) = Q0·Q1 + Q2·M16 = NAND(NAND(Q0,Q1),NAND(Q2,M16)) | ||
(PRG ROM A17 in) = (CHR ROM A17 in) = Q2 | (PRG ROM A17 in) = (CHR ROM A17 in) = Q2 | ||
Further testing has indicated that the internal products (Q0 NAND Q1, Q2 NAND M16) are brought out to test pads for factory verification. | Further testing has indicated that the internal products (Q0 NAND Q1, Q2 NAND M16) are brought out to test pads for factory verification. | ||
The fourth NAND gate is used to invert CIC +RESET to generate 74'161 /CLEAR. | |||
Latest revision as of 04:02, 15 May 2019
iNES Mapper 037 represents the Nintendo of Europe multicart "Super Mario Bros. + Tetris + Nintendo World Cup". It glues together 3 MMC3-compatible games in a single pak.
Overview
- PRG ROM size: 256 KiB
- PRG ROM bank size: 8 KiB inner / 64 or 128 KiB outer
- PRG RAM: Impossible
- CHR capacity: 256 KiB ROM
- CHR bank size: 1 and 2 KiB inner / 128 KiB outer
- Nametable mirroring: Controlled by mapper.
- Subject to bus conflicts: No
Registers
This game, like Super Spike V'Ball + Nintendo World Cup, replaces PRG RAM with a single register to enforce multiple "jail cells" containing each game.
The Outer Bank Select register is cleared by the CIC reset line, so if this multicart is used in a console without a functioning lockout chip, only a full power cycle will get back to the menu.
Outer Bank Select ($6000-$7FFF)
7 bit 0
xxxx xQBB
│││
│└┴── If 3, forces PRG A16 high regardless of Q bit; otherwise
└──── the MMC3's PRG A16 is ANDed with this bit before going to PRG ROM.
Additionally connected to A17 on both PRG and CHR ROM.
In case that wasn't clear:
| Value written | PRG window | 128kB CHR window |
|---|---|---|
| 0,1,2 | $00000-$0FFFF (64kB) | $00000-$1FFFF |
| 3 | $10000-$1FFFF (64kB) | $00000-$1FFFF |
| 4,5,6 | $20000-$3FFFF (128kB) | $20000-$3FFFF |
| 7 | $30000-$3FFFF (64kB) | $20000-$3FFFF |
As far as the MMC3 is concerned, this is the PRG-RAM, so you will need to enable writes to PRG-RAM to update it. Despite that the MMC3 thinks this register is RAM, the register itself does not, so it is not readable and attempting to read it will return open bus.
All other registers ($8000-$FFFF)
See MMC3.
Hardware
Since this pak was only ever released with epoxy covering wirebonded silicon dice, the following is guesswork:
It is very likely that the support hardware is a 74HC161 latch and a 74HC00 quad NAND gate, based on the specific order that the traces enter the epoxy blob. The latch, just like in the discrete logic mappers that use it, latches the bottom 3 bits of the data bus when it is written to. (Below, we call the latched form of D0→Q0, D1→Q1, and D2→Q2). The NAND gates are arranged to calculate
(MMC3 PRG A16 out) = M16 (for brevity) (PRG ROM A16 in) = Q0·Q1 + Q2·M16 = NAND(NAND(Q0,Q1),NAND(Q2,M16)) (PRG ROM A17 in) = (CHR ROM A17 in) = Q2
Further testing has indicated that the internal products (Q0 NAND Q1, Q2 NAND M16) are brought out to test pads for factory verification.
The fourth NAND gate is used to invert CIC +RESET to generate 74'161 /CLEAR.
