UNROM 512

From NESdev Wiki
Revision as of 22:24, 22 May 2014 by Caitsith2 (talk | contribs) (8Bit XMAS revD PCBs and details added.)
Jump to navigationJump to search

UNROM 512 is a discrete-logic board made by RetroUSB as an extension of UNROM with up to 512k of PRG ROM, bankable CHR RAM, an option for mapper-controlled single-screen mirroring, as well as a self-flashable configuration for rewriting PRG.

The iNES format assigns iNES Mapper 030 to UNROM 512.

The UNIF names for this board are UNROM-512-8, UNROM-512-16 and UNROM-512-32, depending on how much CHR RAM is present.

Games that use this board include:


Overview

  • PRG ROM size: Up to 512 KB (Up to 256KB on 8Bit XMAS)
  • PRG ROM bank size: 16 KB
  • PRG RAM: None
  • CHR capacity: Up to 32 KB RAM
  • CHR bank size: 8 KB
  • Nametable mirroring: Solder pads select vertical, horizontal, or mapper-controlled one-screen
  • Subject to bus conflicts: Yes, in the non-flashable configuration

Board

The example board in question is marked as follows: "Sealie Computing", "12/29/2011 revA", "UNROM 512". The backside of the board was mislabeled with "ReproPak MMC3".

The board includes 4x banks worth of full 8KB CHR ram (Configurable by jumpers) and 32x 16KB PRG banks.

The board can be wired in a not flashable, or self flashable configuration. Mirroring can be selected between Horizontal, Vertical, and Mapper controlled One Screen.

Bus conflicts are only present on the non-flashable configuration of the board.

Some images of the board:

When board is not flashable: 

  Registers:
  ---------------------------
  
  Range,Mask:   $8000-FFFF, $8000
  
    $8000:  [MCCP PPPP]
      M = One screen Mirroring select
      C = CHR RAM bank
      P = PRG ROM bank
  
  PRG Setup:
  ---------------------------
       $8000   $A000   $C000   $E000  
      +-------------------------------+
      |     $8000     |     { -1}     |
      +---------------+---------------+
  
  CHR Setup:
  ---------------------------
        $0000   $1000   
      +-------+-------+
      |     $0000     |
      +-------+-------+

When board is self flashable: 

  Registers:
  ---------------------------
  
  Range,Mask:   $8000-BFFF, $8000
                $C000-FFFF, $C000
  
    $8000:  [.... ....]
      Write a sequence of bytes here for writing to the flash. The sequence is as follows 

(This code must exist in wram):
        Erase 4KB Flash Sector:
        $C000:$01, $9555:$AA
        $C000:$00, $AAAA:$55
        $C000:$01, $9555:$80
        $C000:$01, $9555:$AA
        $C000:$00, $AAAA:$55
        $C000:BANK, ADDR:$30 (Where BANK is $00-1F, ADDR is $8000,$9000,$A000,$B000)
        Read the written location twice until you get $FF twice.

        Write a byte:
        $C000:$01, $9555:$AA
        $C000:$00, $AAAA:$55
        $C000:$01, $9555:$A0
        $C000:BANK, ADDR:DATA (Where BANK is $00-1F, ADDR is $8000-$BFFF, DATA is $00-$FF)
        Read the written location twice until you get DATA twice.

Additionally, on 8Bit XMAS boards, any writes here controls the LEDs as follows.

    $8000:  [BYGR bygr]
        B = Blue 3, Blue 4
        Y = Yellow 3, Yellow 4
        G = Green 3, Green 4
        R = Red 3, Red 4
        b = Blue 1, Blue 2
        y = Yellow 1, Yellow 2
        g = Green 1, Green 2
        r = Red 1, Red 2

  
    $C000:  [MCCP PPPP]
      M = One screen Mirroring select
      C = CHR RAM bank
      P = PRG ROM bank
  
  PRG Setup:
  ---------------------------
       $8000   $A000   $C000   $E000  
      +-------------------------------+
      |     $8000     |     { -1}     |
      +---------------+---------------+
  
  CHR Setup:
  ---------------------------
        $0000   $1000   
      +-------+-------+
      |     $8000     |
      +-------+-------+

Here's a schematic of the board: 

             ____
A14 ---------\    \
              )    >--- ROM A14
377 Q0 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A15
377 Q1 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A16
377 Q2 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A17
377 Q3 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A18
377 Q4 ------/____/

16/32KB CHRRAM
377 Q5 --[]--+-- CHRRAM A13
             |
VCC -----[]--+
8KB CHRRAM

8/16KB CHRRAM
VCC -----[]--+
             |
377 Q6 --[]--+-- CHRRAM A14
32KB CHRRAM

ONE
377 Q7 --[]--+
             |
VERT         |
PPU A10 -[]--+-- CIRAM_A10
             |
HORIZ        |
PPU A11 -[]--+

FLASHLOCKED3
R/W ------[]-+
             |
FLASHABLE    |
GND ------[]-+-- 377_/CE

FLASHLOCKED1
VCC ------[]-------+
          ½74LS139 |
          .------. |
CPUA14----|A   Y0|-+- PRGROM_/WE
R/W ------|B   Y1|-+- 377_CLK
          |    Y2| |
/ROMSEL-+-|G   Y3| |
        | '------' |
        |          |
        +---[]-----+
       FLASHLOCKED2

FLASHLOCKED4
GND ------[]-----+
        ½74LS139 |
        .------. |
R/W ----|A   Y0| |
GND ----|B   Y1|-+- PRGROM_/OE
        |    Y2|
/ROMSEL-|G   Y3|
        '------'

With 8Bit Xmas Board, there is a second 377 chip for the LEDs, and 2 jumpers to control whether the 377 is sourcing
current to the LEDs or sinking current from them.  Additionally, the board has no flash control jumpers, and is hard-wired
flashable,  and has no CHR ram control jumpers, is hard-wired as 32KB, and it does not have the second 74LS32 chip,
required for a 512KB board, so its max size is 256KB.

Q0-----R1-----RED1-----RED2-------+
Q1--+--R6-----GRN1----------------+
    +--R5-----GRN2----------------+
Q2-----R3-----YEL1-----YEL2-------+
Q3--+--R9-----BLU1----------------+
    +--R10----BLU2----------------+
Q4-----R2-----RED3-----RED4-------+
Q5--+--R7-----GRN3----------------+
    +--R8-----GRN4----------------+
Q6-----R4-----YEL3-----YEL4-------+
Q7--+--R11----BLU3----------------+
    +--R12----BLU4----------------+
                                  |
VCC---------[]--------------------+
GND---------[]--------------------+

The board is wired in one of the following configurations:

Not Flashable:

  • All 4 Flash Locked jumpers are soldered.
  • Flashable jumper is not soldered.
  • 74*139 is not mounted.
  • This configuration is subject to bus conflicts

Flashable:

  • All 4 Flash Locked jumpers are not soldered.
  • Flashable jumper is soldered.
  • 74*139 is mounted.
  • This configuration is not subject to bus conflicts

The Self-flashable configuration should be implemented according to the SST39SF040's datasheet.

Example flash writing code - Flash.asm

Mapper

NES 2.0 may specify the CHR RAM size from 8 to 32 KB, but the default for iNES should to use 32 KB.

If the Battery flag is set, which indicates the mapper is flashable, then no bus conflicts should be emulated. On the other hand, bus conflicts should be emulated if the battery flag is cleared.

Mapper controlled one-screen mirroring is only emulated if the Four-Screen mirroring flag is set, otherwise, it is hard-locked on either horizontal or vertical mirroring.

Mapper 30 is currently only using sub mapper 0. The other sub mappers are reserved for future use.

Supported in FCEUX as of r3071, Supported in BizHawk as of r6322

Retrieved from "https://www.nesdev.org/w/index.php?title=UNROM_512&oldid=12222"