UNROM 512

Games that use this board include Battle Kid 2: Mountain of Torment and "Study Hall".

The example board in question is marked as follows: "Sealie Computing", "12/29/2011 revA",

"UNROM 512". The backside of the board was mislabeled with "ReproPak MMC3".

The board includes 4x banks worth of full 8KB CHR ram (Configurable by jumpers) and 32x 16KB

PRG banks.

The board can be wired in a not flashable, or self flashable configuration. Mirroring can be

selected between Horizontal, Vertical, and Mapper controlled One Screen.

Bus conflicts are only present on the non-flashable configuration of the board.

some images of the board: Study Hall PCB Front Battle Kid 2 PCB Front PCB Back

When board is not flashable:

  Registers:
  ---------------------------
  
  Range,Mask:   $8000-FFFF, $8000
  
    $8000:  [MCCP PPPP]
      M = One screen Mirroring select
      C = CHR RAM bank
      P = PRG ROM bank
  
  PRG Setup:
  ---------------------------
       $8000   $A000   $C000   $E000  
      +-------------------------------+
      |     $8000     |     { -1}     |
      +---------------+---------------+
  
  CHR Setup:
  ---------------------------
        $0000   $1000   
      +-------+-------+
      |     $0000     |
      +-------+-------+

When board is self flashable:

  Registers:
  ---------------------------
  
  Range,Mask:   $8000-BFFF, $8000
                $C000-FFFF, $C000
  
    $8000:  [.... ....]
      Write a sequence of bytes here for writing to the flash. The sequence is as follows 

(This code must exist in wram):
        Erase 4KB Flash Sector:
        $C000:$01, $9555:$AA
        $C000:$00, $AAAA:$55
        $C000:$01, $9555:$80
        $C000:$01, $9555:$AA
        $C000:$00, $AAAA:$55
        $C000:BANK, ADDR:$30 (Where BANK is $00-1F, ADDR is $8000,$9000,$A000,$B000)
        Read the written location twice until you get $FF twice.

        Write a byte:
        $C000:$01, $9555:$AA
        $C000:$00, $AAAA:$55
        $C000:$01, $9555:$A0
        $C000:BANK, ADDR:DATA (Where BANK is $00-1F, ADDR is $8000-$BFFF, DATA is $00-$FF)
        Read the written location twice until you get DATA twice.
  
    $C000:  [MCCP PPPP]
      M = One screen Mirroring select
      C = CHR RAM bank
      P = PRG ROM bank
  
  PRG Setup:
  ---------------------------
       $8000   $A000   $C000   $E000  
      +-------------------------------+
      |     $8000     |     { -1}     |
      +---------------+---------------+
  
  CHR Setup:
  ---------------------------
        $0000   $1000   
      +-------+-------+
      |     $8000     |
      +-------+-------+

Here's a schematic of the board:

             ____
A14 ---------\    \
              )    >--- ROM A14
377 O0 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A15
377 O1 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A16
377 O2 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A17
377 O3 ------/____/

             ____
A14 ---------\    \
              )    >--- ROM A18
377 O4 ------/____/

16/32KB CRAM
377 O5 --[]--+-- CRAM A13
             |
VCC -----[]--+
8KB CRAM

8/16KB CRAM
VCC -----[]--+
             |
377 O6 --[]--+-- CRAM A14
32KB CRAM

ONE
377 O7 --[]--+
             |
VERTICAL     |
CHR A10 -[]--+-- CA10_VRAM
             |
HORIZONTAL   |
CHR A11 -[]--+

Flash Locked 1
VCC ---[]--- ROM_/WE

Flash Locked 2
P/CE --[]--- 377_CLK

Flash Locked 3
P_RW --[]--- 377_/CE

Flash Locked 4
GND ---[]--- ROM_/OE

Flashable
GND ---[]--- 377_/CE

        _________
A14 ----| A   Y0|--- ROM_/WE
P_RW ---| B   Y1|--- 377_CLK
        |     Y2|
P_/CE --| G   Y3|
        ---------
          74*139
        _________
P_RW ---| A   Y0|
GND ----| B   Y1|--- ROM_/OE
        |     Y2|
P_/CE --| G   Y3|
        ---------

The board is wired in one of the following configurations:

Not Flashable:

All 4 Flash Locked jumpers are soldered.
Flashable jumper is not soldered.
74*139 is not mounted.

This configuration is subject to bus conflicts

Flashable:

All 4 Flash Locked jumpers are not soldered.
Flashable jumper is soldered.
74*139 is mounted.

This configuration is not subject to bus conflicts