|
|
| Line 1: |
Line 1: |
| The '''flags''' register, also called '''processor status''' or just '''P''', is one of the six architectural registers on the 6502 family CPU.
| | #REDIRECT [[Status flags]] |
| It is composed of six one-bit registers (see [[Status flags]]); instructions modify one or more bits and leave others unchanged.
| |
| | |
| Instructions that save or restore the flags map them to bits in the architectural 'P' register as follows:
| |
| | |
| 7 bit 0
| |
| ---- ----
| |
| NVss DIZC
| |
| |||| ||||
| |
| |||| |||+- Carry: 1 if last addition or shift resulted in a carry, or if
| |
| |||| ||| last subtraction resulted in no borrow
| |
| |||| ||+-- Zero: 1 if last operation resulted in a 0 value
| |
| |||| |+--- Interrupt: Interrupt inhibit
| |
| |||| | (0: /IRQ and /NMI get through; 1: only /NMI gets through)
| |
| |||| +---- Decimal: 1 to make ADC and SBC use binary-coded decimal arithmetic
| |
| |||| (ignored on second-source 6502 like that in the NES)
| |
| ||++------ s: No effect, used by the stack copy, see note below
| |
| |+-------- Overflow: 1 if last ADC or SBC resulted in signed overflow,
| |
| | or D6 from last BIT
| |
| +--------- Negative: Set to bit 7 of the last operation
| |
| | |
| == The B flag ==
| |
| There are six and only six flags in the processor status register within the CPU.
| |
| Despite what some 6502 references might appear to claim on a first reading, there is no "B flag" stored within the CPU's status register.
| |
| | |
| Two interrupts (/[[IRQ]] and /[[NMI]]) and two instructions (PHP and BRK) push the flags to the stack. In the byte pushed, bit 5 is always set to 1, and bit 4 is 1 if from an instruction (PHP or BRK) or 0 if from an interrupt line being pulled low (/IRQ or /NMI). This is the only time and place where the B flag actually exists: not in the status register itself, but in bit 4 of the copy that is written to the stack.
| |
| | |
| {| class="tabular"
| |
| |-
| |
| ! Instruction || Bits 5 and 4 || Side effects after pushing
| |
| |-
| |
| | PHP || 11 || None
| |
| |-
| |
| | BRK || 11 || I is set to 1
| |
| |-
| |
| | /[[IRQ]] || 10 || I is set to 1
| |
| |-
| |
| | /[[NMI]] || 10 || I is set to 1
| |
| |}
| |
| Two instructions (PLP and RTI) pull a byte from the stack and set all the flags. They ignore bits 5 and 4.
| |
| | |
| The only way for an IRQ handler to distinguish /IRQ from BRK is to read the flags byte from the stack and test bit 4.
| |
| The slowness of this is one reason why BRK wasn't used as a syscall mechanism.
| |
| Instead, it was more often used to trigger a patching mechanism that hung off the /IRQ vector: a single byte in PROM, UVEPROM, flash, etc. would be forced to 0, and the IRQ handler would pick something to do instead based on the program counter.
| |
| | |
| Unlike bits 5 and 4, bit 3 actually exists in P, even though it doesn't affect the ALU operation on the 2A03 or 2A07 CPU the way it does in MOS Technology's own chips.
| |
| | |
| == External links ==
| |
| *[http://forums.nesdev.org/viewtopic.php?p=64224#p64224 koitsu's explanation]
| |
