PPU registers

The PPU exposes only eight memory-mapped registers to the CPU. These nominally sit at $2000 through $2007 in the CPU's address space, but because they're incompletely decoded, they're mirrored in every 8 bytes from $2008 through $3FFF, so a write to $3456 is the same as a write to $2006.

Note: The next paragraph explain details that should be more in the getting started reference?

Immediately after powerup, the PPU must wait at least one full frame before it is stable enough to operate normally. The first thing that should be done on startup is to write a zero byte to registers PPUCTRL and PPUMASK (to disable rendering and NMIs) and then wait for bit 7 of PPUSTATUS to be set twice. Some programs will wait for $2002 bit 7 to be set, initialize hardware other than the PPU (such as zeroing CPU RAM), and then wait for $2002 bit 7 to be set again.

Controller ($2000) > write

Is often referred as PPUCTRL.

Various flags controlling PPU operation

76543210
||||||||
||||||++- Base nametable address
||||||    (0 = $2000; 1 = $2400; 2 = $2800; 3 = $2C00)
|||||+--- VRAM address increment per CPU read/write of PPUDATA
|||||     (0: increment by 1, going across; 1: increment by 32, going down)
||||+---- Sprite pattern table address for 8x8 sprites (0: $0000; 1: $1000)
|||+----- Background pattern table address (0: $0000; 1: $1000)
||+------ Sprite size (0: 8x8; 1: 8x16)
|+------- PPU master/slave select (has no effect on the NES)
+-------- Generate an NMI at the start of the
          vertical blanking interval (0: off; 1: on)

Equivalently, bits 0 and 1 are the most significant bit of the scrolling coordinates (see Nametables and PPU scroll):

76543210
      ||
      |+- 1: Add 256 to the X scroll position
      +-- 1: Add 240 to the Y scroll position

Note

Another way of seeing the explanation above is that when you reach the end of a nametable, you must switch to the next one, hence, changing the nametable address.

Mask ($2001) > write

is often referred as PPUMASK.

Screen enable, masking, and intensity

76543210
||||||||
|||||||+- Grayscale (0: normal color; 1: AND all palette entries
|||||||   with 0x30, effectively producing a monochrome display;
|||||||   note that colour emphasis STILL works when this is on!)
||||||+-- Enable background in leftmost 8 pixels of screen (0: clip; 1: display)
|||||+--- Enable sprite in leftmost 8 pixels of screen (0: clip; 1: display)
||||+---- Enable background rendering
|||+----- Enable sprite rendering
||+------ Intensify reds (and darken other colors)
|+------- Intensify greens (and darken other colors)
+-------- Intensify blues (and darken other colors)

Status ($2002) < read

Is often referred as PPUSTATUS.

PPU status

76543210
||||||||
|||+++++- Unimplemented
||+------ Sprite overflow. The PPU can handle only eight sprites on one
||        scanline and sets this bit if it starts dropping sprites.
||        Normally, this triggers when there are 9 sprites on a scanline,
||        but the actual behavior is significantly more complicated.
|+------- Sprite 0 Hit.  Set when a nonzero pixel of sprite 0 'hits'
|         a nonzero background pixel.  Used for raster timing.
+-------- Vertical blank has started (0: not in VBLANK; 1: in VBLANK)

Notes

• Reading the status register will clear D7 mentioned above and also the address latch used by [[Scroll ($2005) >> write x2|PPUSCROLL]] and PPUADDR.

• Caution: Reading PPUSTATUS at the exact start of vertical blank will return a 0 in D7 but clear the latch anyway, causing the program to miss frames. See NMI for details.

OAM address ($2003) > write

Is often referred as OAMADDR.

Write the address of OAM you want to access here. Most games just write $00 here and then use OAM_DMA ($4014).

This register also seems to affect Sprite 0 Hit, though it is not yet understood exactly how it does. The upper 5 bits of this register seem to select which SPR-RAM data is used for sprites 0 and 1 (instead of the first 8 bytes of SPR-RAM), though actual behavior varies between resets.

OAM data ($2004) <> read/write

Is often referred as OAMDATA.

OAM data port.

Write OAM data here. Writes will increment OAMADDR; reads won't.

Most games access this register through $4014 instead. Reading OAMDATA while the PPU is rendering will expose internal OAM accesses during sprite evaluation and loading; Micro Machines does this.

Scroll ($2005) >> write x2

Is often referred as PPUSCROLL.

After reading PPUSTATUS to reset the address latch, write the horizontal and vertical scroll offsets here just before turning on the screen:

 bit PPUSTATUS
 ; possibly other code goes here
 lda cam_position_x
 sta PPUSCROLL
 lda cam_position_y
 sta PPUSCROLL

Horizontal offsets range from 0 to 255. "Normal" vertical offsets range from 0 to 239. (Values of 240 to 255 are treated as -16 through -1 in a way, pulling tile data from the attribute table.)

Editing note: some information should be in the getting started section instead of here. It doesn't say explicitly you have to do 2 write: first X value then Y. Must change text.

Address ($2006) >> write x2

Is often referred as PPUADDR

VRAM address register.

After reading PPUSTATUS to reset the address latch, write the 16-bit address of VRAM you want to access here, upper byte first. Valid addresses are $0000-$3FFF.

note

Access to PPUSCROLL and PPUADDR during screen refresh produces interesting raster effects; the starting position of each scanline can be set to any pixel position in nametable memory. For more information, see "The Skinny on NES Scrolling" by loopy, available from the main site.

Editor's note: Last comment about external page should be re-directed to the getting started section instead.

Data ($2007) <> read/write

Is often referred as PPUDATA.

VRAM data register.

When the screen is turned off by disabling the background/sprite rendering flag with the PPUMASK or during vertical blank, you can read or write data from VRAM through this port.

Note

Reads are delayed by one cycle; discard the first byte read. Do not attempt to access this register while the PPU is rendering; if you do, Bad Things™ will happen (i.e. graphical glitches and RAM corruption).