PRG RAM circuit

The iNES format implies 8 KiB of PRG RAM at $6000-$7FFF, which may or may not be battery backed, even for discrete boards such as NROM and UxROM that never actually had RAM there. This inspired some people on the nesdev.org BBS to come up with circuits to add PRG RAM to the original boards, so that games relying on it can run on an NES. The primary problem is in producing the enable signals for a 62256 or 6264 static RAM or compatible PSRAM.

kyuusaku's circuit

On the forum, kyuusaku and Bregalad discussed PRG RAM decoder circuits built from 7400 series parts to approximate this behavior in an NES cartridge board. The first tries took two chips[1] or had possible timing problems.[2][3] They settled on the following circuits:

Using 7410

kyuusaku suggested a circuit based on a 74HC10 (triple three-input NAND) stick a pulldown on CE2 to take advantage of Phi2 going high-impedance during reset in order to "offer some write protection".[4]

           ,-------------- ROM /CE
          |   ____
/ROMSEL --+--|    `-.
             |       \
A14 ---------|        )o-- RAM /CE
             |       /
A13 ---------|____,-'

              ____
+5V ------+--|    `-.
          |  |       \
          `--|        )o-- ROM /OE
             |       /
R/W ------+--|____,-'
          |
          `--------------- RAM /WE

Phi2 ---------+----------- RAM CE2
              |
              <
              < "big R"
              <
              |
GND ----------+----------- RAM /OE

Using 7420

He also suggested a circuit based on a 74HC20 (double 4-input NAND), which appears to be the same one in Family BASIC:

Or you could just use a NAND4 to decode any active low memory, also using the /WE priority method. If this is done with a two gate 7420, the second gate could be used to invert r/w to prevent bus conflicts as in the circuit above. This is probably the *final* best way unless you happen to need the extra AND3 from the 7410 and have a positive CE.

The pinout:

• A = Phi2
• B = /ROMSEL
• C = A14
• D = A13
• Y = PRG RAM /CE
• PRG RAM /OE = GND
• PRG RAM /WE = Vcc or R//W, depending on the Family BASIC cart's write-protect switch

Kevin Horton suggested the same circuit.

You could also use the other gate to invert R//W for /OE on the ROM to prevent bus conflicts.

Using 74139

If you don't need bus conflict prevention, you can use a 74HC139 (double 2-to-4 decoder), which may be cheaper or have better timing than a 74HC20. This circuit resembles the decoder in Jaleco's discrete mappers (87 and 140), which uses a 74139 to decode a single mapper register to $6000-$7FFF.

• 1/E = GND
• 1A0 = M2
• 1A1 = A14
• 2/E = 1/Y3
• 2A0 = A13
• 2A1 = PRG /CE
• PRG RAM /CE = 2/Y3

Proof:

1A0	1A1	1/Y3	2A0	2A1	2/Y3
0	x	1	x	x	1
1	0	1	x	x	1
1	1	0	1	x	1
1	1	0	0	1	1
1	1	0	1	1	0

See further suggestions from kyuusaku.

The PlayChoice version of Mike Tyson's Punch-Out!! uses an extra IC to add battery-backed RAM. The digits in existing photos are hard to read, but it is believed to be a 74HC139. Its wiring has not been traced.

PRG /CE delay

One thing that can complicate adding PRG RAM to a board is the fact that PRG /CE and M2, used together to decode $6000-$7FFF, do not change at the same time. PRG /CE is the logical NAND of M2 and PRG A15. This is accomplished by sending M2 and PRG A15 into a 74LS139 two-to-four line decoder on the NES main board. This introduces a small delay of up to 33 ns between the time M2 rises and the time PRG /CE falls.

If this delay is too long it can cause unintentional writes to PRG RAM when writing to mapper registers $E000-$FFFF.

This is not a problem for the original cartridge hardware because the RAM chips used require a /WE (Write Enable) pulse of at least 50ns to 70ns depending on the chip. This means that the spurious /WE signal generated by this delay (MAX 33ns) will not be sufficient to trigger a write on the RAM chip. The circuits above give even more head-room as they tie PRG RAM /OE to ground and decode to /CE. The /CE to end of write timing is typically longer than the minimum /WE pulse width.

If your RAMs are faster than these timing specifications, your decoding logic must delay M2 by about 33 ns to match the PRG /CE delay, as in the 74139-based circuit shown above. In this post, lidnariq suggested adding a resistor and capacitor:

card edge M2 --- 1k --- + --- 7420
                        |
                       33pF
                        |
                       GND

PRG /CE delay issues

The delay is obtained by decreasing the voltage rise speed down to R*C. However, the rise speed cannot be too slow because it might produce oscillation at the digital input (digital chips have minimum rising speed announced in its datasheet). The other way might be not to delay M2 but instead - filter quick pulses on RAM /CE down by using capactor connected to ground or power supply (1 nF should be enough).

                      ______________________________________________________
card edge M2 --------| combinatory circuit that outputs                     |----+-----|/CE
card edge /ROMSEL ---| 0 when M2 = '1', /ROMSEL = '0', A14 = '1', A13 = '1' |    |     |
card edge A14     ---| 1 otherwise                                          |    1nf   |   RAM 
card edge A13 -------|______________________________________________________|    |     |_________
                                                                             GND or +5V

If you are using any programmable circuit (FPGA) to simulate mapper behaviour that latches data/adderess at $4020-$6FFF and you are doing it at the falling edge of M2, you don't need to worry about PRG/CE delay because on falling edge of M2 the /ROMSEL line has correct logic level.

Batter backup

Adding battery backup to RAM (probably most ofter used for WRAM at $6000-$7FFF) might be useful to maintain data between power cut offs. Most RAMs have special data retention mode, which decreases current consumption to few microamps, still having its data not lost, but the followings need to be fullfilled:

• voltage supply in data retention mode Vret should be >= 2 V and <= ordinary power supply voltage Vcc (CRC2032 3.3 V battery is typically used for maintaining memory power),
• memory must become deselected before supply voltage drops from Vcc to Vret,
• memory must remain deselected for the whole time Vret is supplied.

                    D1           ___________
    5V -------------|>|--+      |       RAM
                         |---+--| VCC
    3.3V battery----|>|--+   |  |
                    D2       R1 |
                             |  |
   RAM /CE decoding logic----+--| /CE
                                |___________

D1 does not allow the 3.3 V battery to power whole cartridge when in standby mode, D2 does not allow the 5 V to load the battery (you can omit it if you have recherchable accumulator), R1 (100 k should be enough) ties /CE at high level when power is cut off.

If you RAM /CE decoding logic does not become high impedance in power off mode, the voltage at RAM /CE might drop after power down (for example - AX5202P DIL40 pirate MMC3 chip seems to have its RAM /CE output at very low resistance with respect to ground when not powered - the above circuit after cutting power makes RAM /CE voltage drop to 1 V which leads to data corruption). To protect against that situation, RAM /CE decoding logic path must become open circuit after powering off. The following transistor is essentially a switch that does the job:

                                 D1           ___________
    5V --------------------------|>|--+      |       RAM
                                      |---+--| VCC
    3.3V battery-----------------|>|--+   |  |
                                 D2       R1 |
                                          |  |
    RAM /CE decoding logic--- E   C ------+--| /CE
                             \____/          |___________
                                | B  NPN
    5V -------------------------+

When no 5V is present or 5V is present but RAM /CE decoding circuit outputs high level, transistor is open. When 5V is present and RAM /CE decoding circuit outputs low level, RAM /CE becomes low.

See also: Battery circuit schematic

References

• Loopy pointed out the PRG /CE delay here.
• Further investigation performed in this thread.
• 6264P-12 8Kx8 SRAM Data Sheet
• PRG-RAM decoding circuitry - problems [5]