User:NovaSquirrel/Nova-7: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
m (→‎CHR Bank 0-7 ($0-7): illustration of the modes)
 
(3 intermediate revisions by the same user not shown)
Line 5: Line 5:
* PRG ROM bank size: 8 KB
* PRG ROM bank size: 8 KB
* PRG RAM: Up to 1024 KB
* PRG RAM: Up to 1024 KB
* CHR capacity: Up to 256 KB RAM or ROM
* CHR capacity: 32 KB or 128 KB CHR RAM
* CHR bank size: .5 KB to 4 KB
* CHR bank size: .5 KB to 4 KB
* Interrupts: scanline-based
* Nametable [[mirroring]]: Controlled by mapper; horizontal, vertical, single screen or four screen
* Nametable [[mirroring]]: Controlled by mapper; horizontal, vertical, single screen or four screen
* Subject to [[bus conflict]]s: No
* Subject to [[bus conflict]]s: No
CHR can be 256 KB, but 8 bits is not enough to cover the entire 256 KB with .5 KB banks and the source of the 9th bit is undefined. With RAM, this would also require two 128 KB SRAMs and hardware to select one. CHR can also be ROM but this would make the four screen mode much less useful.


== Registers ==
== Registers ==


Configuration is accomplished by first writing the command number to the Command Register at $5000-57FF, then writing the command's parameter byte to the Parameter Register at $5800-5FFF. If $8000-$FFFF is write-protected, $8000-9FFF and $A000-BFFF will also work for the command and parameter registers, respectively.
Like with FME-7 and MMC3, configuration is accomplished by first writing the command number to the Command Register at $5000-57FF, then writing the command's parameter byte to the Parameter Register at $5800-5FFF. If $8000-$FFFF is write-protected, $8000-9FFF and $A000-BFFF will also work for the command and parameter registers, respectively.


There are 15 commands:
There are 15 commands:
Line 18: Line 21:
* '''$8-B, E''' control PRG banking
* '''$8-B, E''' control PRG banking
* '''$C''' controls nametable mirroring and CHR mode and write protect
* '''$C''' controls nametable mirroring and CHR mode and write protect
* '''$F''' controls IRQ
* '''$F''' controls scanline interrupts


$D is reserved
$D is reserved
Line 35: Line 38:
  |||| ||||
  |||| ||||
  ++++-++++- The parameter to use for this command. Writing to this register invokes the command in the Command Register.
  ++++-++++- The parameter to use for this command. Writing to this register invokes the command in the Command Register.
=== Scanline IRQ register ($4800-4FFF) ===
Writes go to the scanline IRQ register at $0F


== Commands ==
== Commands ==


=== CHR Bank 0-7 ($0-7) ===
=== CHR Bank 0-7 ($0-7) ===
[[File:Nova7_modes.png|thumb]]
  7  bit  0
  7  bit  0
  ---- ----
  ---- ----
Line 77: Line 84:
|}
|}


=== PRG Bank 1-3 ($9-B, $E) ===
=== PRG Bank 0-4 ($8-B, $E) ===
  7  bit  0
  7  bit  0
  ---- ----
  ---- ----
Line 107: Line 114:
   |++------ CHR bank switching mode
   |++------ CHR bank switching mode
   +-------- If 0, any RAM at $8000-FFFF is write protected
   +-------- If 0, any RAM at $8000-FFFF is write protected
When combined with sprite 0 or the scanline IRQ feature, this allows four-screen mirroring and a status bar at the same time, as the playfield is in CHR RAM and the status bar is in CIRAM.


=== IRQ Control ($F) ===
=== IRQ Control ($F) ===

Latest revision as of 23:00, 28 October 2015

This proposal for an NES mapper combines the runtime flexibility of CHR RAM with the tile animation capability of CHR ROM.

Overview

  • PRG ROM size: Up to 1024 KB
  • PRG ROM bank size: 8 KB
  • PRG RAM: Up to 1024 KB
  • CHR capacity: 32 KB or 128 KB CHR RAM
  • CHR bank size: .5 KB to 4 KB
  • Interrupts: scanline-based
  • Nametable mirroring: Controlled by mapper; horizontal, vertical, single screen or four screen
  • Subject to bus conflicts: No

CHR can be 256 KB, but 8 bits is not enough to cover the entire 256 KB with .5 KB banks and the source of the 9th bit is undefined. With RAM, this would also require two 128 KB SRAMs and hardware to select one. CHR can also be ROM but this would make the four screen mode much less useful.

Registers

Like with FME-7 and MMC3, configuration is accomplished by first writing the command number to the Command Register at $5000-57FF, then writing the command's parameter byte to the Parameter Register at $5800-5FFF. If $8000-$FFFF is write-protected, $8000-9FFF and $A000-BFFF will also work for the command and parameter registers, respectively.

There are 15 commands:

  • $0-7 control CHR banking
  • $8-B, E control PRG banking
  • $C controls nametable mirroring and CHR mode and write protect
  • $F controls scanline interrupts

$D is reserved

Command Register ($5000-$57FF)

7  bit  0
---- ----
.... CCCC
     ||||
     ++++- The command number to invoke when writing to the Parameter Register

Parameter Register ($5800-$5FFF)

7  bit  0
---- ----
PPPP PPPP
|||| ||||
++++-++++- The parameter to use for this command. Writing to this register invokes the command in the Command Register.

Scanline IRQ register ($4800-4FFF)

Writes go to the scanline IRQ register at $0F

Commands

CHR Bank 0-7 ($0-7)

Nova7 modes.png
7  bit  0
---- ----
BBBB BBBB
|||| ||||
++++-++++- The bank number to select for the specified bank.
Register CHR mode 0 CHR mode 1 CHR mode 2 CHR mode 3
$0 $0000-$03FF $0000-$07FF $0000-$07FF $0000-$0FFF
$1 $0400-$07FF $0800-$0BFF $0800-$0FFF $1000-$13FF
$2 $0800-$0BFF $0C00-$0FFF $1000-$13FF $1400-$05FF
$3 $0C00-$0FFF $1000-$07FF $1400-$07FF $1600-$07FF
$4 $1000-$13FF $1800-$19FF $1800-$19FF $1800-$19FF
$5 $1400-$17FF $1A00-$1BFF $1A00-$1BFF $1A00-$1BFF
$6 $1800-$1BFF $1C00-$1DFF $1C00-$1DFF $1C00-$1DFF
$7 $1C00-$1FFF $1E00-$1FFF $1E00-$1FFF $1E00-$1FFF

PRG Bank 0-4 ($8-B, $E)

7  bit  0
---- ----
RBBB BBBB
|||| ||||
|+++-++++- The bank number to select for the specified bank.
+--------- If 1, bank is RAM instead of ROM
Bank $8 - CPU $6000-$7FFF
Bank $9 - CPU $8000-$9FFF
Bank $A - CPU $A000-$BFFF
Bank $B - CPU $C000-$DFFF
Bank $E - CPU $E000-$FFFF

Loss of M2 oscillation (caused by resets) causes register $0E to revert to a value of $7F, mapping the last ROM bank in the cart into $E000-$FFFF.

Nametable/CHR control ($C)

7  bit  0
---- ----
.WCC SFMM
 ||| ||||
 ||| ||++- Mirroring Mode
 ||| ||     0 = Vertical
 ||| ||     1 = Horizontal
 ||| ||     2 = One Screen Mirroring from $2000 ("1ScA")
 ||| ||     3 = One Screen Mirroring from $2400 ("1ScB")
 ||| |+--- If 1, four screen mirroring in last 4KB of CHR RAM, ignores mm if on
 ||| +---- If 1, swap PPU $0xxx with $1xxx
 |++------ CHR bank switching mode
 +-------- If 0, any RAM at $8000-FFFF is write protected

When combined with sprite 0 or the scanline IRQ feature, this allows four-screen mirroring and a status bar at the same time, as the playfield is in CHR RAM and the status bar is in CIRAM.

IRQ Control ($F)

7  bit  0
---- ----
NNNN NNNN
++++-++++- Scanlines until IRQ

At the start of each scanline, the PPU freezes for a few cycles, and PPU A13 stays high for at least three consecutive cycles of PPU /RD. The mapper detects this and subtracts 1 from the value in $0F unless the value is $F0-$FF. While the value is 0, /IRQ is pulled low. Programming tip: Reading from the nametables or palette during vertical or forced blanking will cause counts unless you write $FF to port $0F.