INES Mapper 159

iNES Mapper 159 is used for Bandai FCG boards with an LZ93D50 ASIC and a 128-byte serial EEPROM (24C01). The 128 bytes must be denoted as PRG-NVRAM in the NES 2.0 header using byte value $10.

Game List

• Dragon Ball Z: Kyoushuu! Saiya-jin
• Magical Taruruuto-kun: Fantastic World!!
• Magical Taruruuto-kun 2: Mahou Daibouken
• SD Gundam Gaiden - Knight Gundam Monogatari

Banks

• CPU $8000-$BFFF: 16 KiB switchable PRG ROM bank
• CPU $C000-$FFFF: 16 KiB PRG ROM bank, fixed to the last bank
• PPU $0000-$03FF: 1 KiB switchable CHR ROM bank
• PPU $0400-$07FF: 1 KiB switchable CHR ROM bank
• PPU $0800-$0BFF: 1 KiB switchable CHR ROM bank
• PPU $0C00-$0FFF: 1 KiB switchable CHR ROM bank
• PPU $1000-$13FF: 1 KiB switchable CHR ROM bank
• PPU $1400-$17FF: 1 KiB switchable CHR ROM bank
• PPU $1800-$1BFF: 1 KiB switchable CHR ROM bank
• PPU $1C00-$1FFF: 1 KiB switchable CHR ROM bank

Registers

Read Serial EEPROM ($6000-$7FFF read)

Mask: $E000

7  bit  0
---- ----
xxxE xxxx
|||| ||||
+++|-++++- Open bus
   +------ Data out from I²C EEPROM

CHR-ROM Bank Select ($8000-$8007 write)

Mask: $800F

7  bit  0
---- ----
CCCC CCCC
|||| ||||
++++-++++-- 1 KiB CHR-ROM bank number

• $xxx0: Select 1 KiB CHR-ROM bank at PPU $0000-$03FF
• $xxx1: Select 1 KiB CHR-ROM bank at PPU $0400-$07FF
• $xxx2: Select 1 KiB CHR-ROM bank at PPU $0800-$0BFF
• $xxx3: Select 1 KiB CHR-ROM bank at PPU $0C00-$0FFF
• $xxx4: Select 1 KiB CHR-ROM bank at PPU $1000-$13FF
• $xxx5: Select 1 KiB CHR-ROM bank at PPU $1400-$17FF
• $xxx6: Select 1 KiB CHR-ROM bank at PPU $1800-$1BFF
• $xxx7: Select 1 KiB CHR-ROM bank at PPU $1C00-$1FFF

PRG-ROM Bank Select ($8008 write)

Mask: $800F

7  bit  0
---- ----
.... PPPP
     ||||
     ++++-- Select 16 KiB PRG-ROM bank at CPU $8000-$BFFF   

Nametable Mirroring Type Select ($8009 write)

Mask: $800F

7  bit  0
---- ----
.... ..MM
       ||
       ++-- Select nametable mirroring type

0: Vertical 1: Horizontal 2: One-screen, page 0 3: One-screen, page 1

IRQ Control ($800A write)

Mask: $800F

7  bit  0
---- ----
.... ...C
        |
        +-- IRQ counter control

0: Counting disabled 1: Counting enabled

• Writing to this register acknowledges a pending IRQ, and copies the latch to the actual counter.
• If a write to this register enables counting while the counter is holding a value of zero, an IRQ is generated immediately.

IRQ Latch ($800B-$800C write)

Mask: $800F

   $C         $B
7  bit  0  7  bit  0
---- ----  ---- ----
CCCC CCCC  CCCC CCCC
|||| ||||  |||| ||||
++++-++++--++++-++++-- Counter value (little-endian)

• If counting is enabled, the counter decreases on every M2 cycle. When it holds a value of zero, an IRQ is generated.
• These registers modify a latch that will only be copied to the actual counter when register $xxxA is written to.

EEPROM Control ($800D write)

Mask: $800F

7  bit  0
---- ----
RDC. ....
|||
||+-------- I²C SCL
|+--------- I²C SDA
+---------- Direction bit (1=Enable Read)

• This register only has an effect if a 24C01 EEPROM is present.
• Please refer to generic I²C tutorials and the 24C01 datasheet on how to operate or emulate this register correctly.