PPU rendering

Work in progress, do not alter.

TODO: Rename this as PPU Rendering instead of PPU Background Evaluation?

The PPU contains the following:

• 2 16-bit shift registers - These contain the bitmap data for two tiles. Every 8 cycles, the bitmap data for the next tile is loaded into the upper 8 bits of this shift register. Meanwhile, the pixel to render is fetched from one of the lower 8 bits.
• 2 8-bit shift registers - These contain the palette attributes for the lower 8 pixels of the 16-bit shift register. These registers are fed by a latch which contains the palette attribute for the next tile. Every 8 cycles, the latch is loaded with the palette attribute for the next tile.

Every cycle, a bit is fetched from these 4 shift registers in order to create a pixel on screen. Exactly which bit is fetched depends on the fine X scroll, set by $2005 (this is how fine X scrolling is possible). Afterwards, the shift registers are shifted once, to the data for the next pixel.

Every 8 cycles/shifts, new data is loaded into these registers.

NTSC PPU

The PPU renders 262 scanlines per frame. Each scanline lasts for 341 PPU clock cycles (113.667 CPU clock cycles; 1 CPU cycle = 3 PPU cycles), with each clock cycle producing one pixel.

Scanline -1 or 261

This is a dummy scanline, whose sole purpose is to perform the sprite evaluation for the next scanline, and to fill the shift registers with the data for the first two tiles of the next scanline. Although no pixels are rendered for this scanline, the PPU still makes the same memory accesses it would for a regular scanline.

Scanlines 0-239

These are the visible scanlines, which contain the graphics to be displayed on the screen. During these scanlines, the PPU is busy fetching data, so the program should not access PPU memory during this time, unless rendering is turned off.

Cycles 0-255

The data for each tile is fetched during this phase. Each memory access takes 2 PPU cycles to complete, and 4 must be performed per tile:

1. Nametable byte
2. Attribute table byte
3. Tile bitmap A
4. Tile bitmap B (+8 bytes from tile bitmap A)

The data fetched from these accesses is placed into internal latches, and then fed to the appropriate shift registers when it's time to do so (every 8 cycles). Because the PPU can only fetch an attribute byte every 8 cycles, each sequential string of 8 pixels is forced to have the same palette attribute.

Note: At the beginning of each scanline, the data for the first two tiles is already loaded into the shift registers (and ready to be rendered), so the first tile that gets fetched is Tile 3.

While all of this is going on, sprite evaluation for the next scanline is taking place as a seperate process, independent to what's happening here.

TODO: Explain how sprite display ties into this process.

Cycles 256-319

The tile data for the sprites on the next scanline are fetched here. Again, each memory access takes 2 PPU cycles to complete, and 4 are performed for each of the 8 sprites:

1. Garbage nametable byte
2. Garbage nametable byte
3. Tile bitmap A
4. Tile bitmap B (+8 bytes from tile bitmap A)

The garbage fetches occur so that the same circuitry that performs the BG tile fetches could be reused for the sprite tile fetches.

If there are less than 8 sprites on the next scanline, then dummy tile fetches occur for the left-over sprites. This data is then discarded, and the sprites are loaded with a transparent bitmap instead.

Cycles 320-335

This is where the first two tiles for the next scanline are fetched, and loaded into the shift registers. Again, each memory access takes 2 PPU cycles to complete, and 4 are performed for the two tiles:

1. Nametable byte
2. Attribute table byte
3. Tile bitmap A
4. Tile bitmap B (+8 bytes from tile bitmap A)

Cycles 336-339

Two bytes are fetched, but the purpose for this is unknown. These fetches are 2 PPU cycles each.

1. Nametable byte
2. Nametable byte

Cycle 340

The PPU idles for one cycle.

Scanline 240

The PPU just idles during this scanline. However, this scanline is not considered part of VBlank.

Scanlines 241-260

These occur during VBlank. The VBlank flag of the PPU is pulled low during scanline 241, so the VBlank NMI occurs here. During this time, the PPU makes no memory accesses, so PPU memory can be freely accessed by the program.